Открытый доступ Открытый доступ  Ограниченный доступ Доступ для подписчиков

Влияние борирования и алитирования на износостойкость стали AISI 1010

Эрсан Мертгенч, Юсуф Каялы, Шюкрю Талаш

Аннотация


Исследованы структура и трибологические свойства стали AISI 101 после борирования и алитирования в порошкообразных смесях при 850° C в течение 1, 3, 5 ч. Определено влияние длительности химико-термической обработки на толщину диффузионного слоя, твердость поверхности и скорость износа стали AISI 101. Проведены рентгеноструктурный и рентгеновской энергодисперсионный анализы, а также испытания на адгезию по классификации Daimler Benz. Показано удовлетворительное состояние поверхностных слоев как после борирования, так и после алитирования.

Ключевые слова


boronizing; aluminizing; wear resistance; steel AISI 1010

Полный текст:

PDF

Литература


Pezzato L., Brunelli K., Dolcet P., Dabala M. Plasma electrolytic oxidation coating produced on 39NiCrMo3 steel // Surface & Coatings Technology. 2016. V. 307. P. 73 - 80.

Fayomi O. S. I., Popoola A. P. I., Aigbodion V. S. Investigation on microstructural, anti-corrosion and mechanical properties of doped Zn - Al - SnO2 metal matrix composite coating on mild steel // Journal of Alloys and Compounds. 2015. V. 623. P. 328 - 334.

Yang W., Li Q., Liu W. et al. Characterization and properties of plasma electrolytic oxidation coating on low carbon steel fabricated from aluminate electrolyte // Vacuum. 2017. V. 144. P. 207 - 216.

Sudiro T., Hia A. I. J., Ciswandi D. et al. High temperature cyclic oxidation resistance of 50Cr - 50Al coatings mechanically alloyed on low carbon steel // Journal of Alloys and Compounds. 2018. V. 732. P. 655 - 665.

Ghahabi E., Shajari Y., Razavi M. et al. Effect of iron content on the wear behavior and adhesion strength of TiC - Fe nanocomposite coatings on low carbon steel produced by air plasma spray // Ceramics International. 2020. V. 46. P. 2670 - 2676.

Mertgenc E., Kesici O. F., Kayali Y. Investigation of wear properties of borided austenitic stainless steel different temperatures and times // Materials Research Express. 2019. V. 6. No. 076420.

Lv Y., Lei L., Sun L. Effect of shot peening on the fatigue resistance of laser surface melted 20CrMnTi steel gear // Materials Science & Engineering A. 2015. V. 629. P. 8 - 15.

Zhang P., Zhang F. C., Yan Z. G. et al. Wear property of low-temperature bainite in the surface layer of a carburized low carbon steel // Wear. 2011. V. 271. P. 697 - 704.

Wang Y., Yang Z., Zhang F., Wu D. Microstructures and mechanical properties of surface and center of carburizing 23Cr2Ni2Si1Mo steel subjected to low-temperature austempering // Materials Science & Engineering A. 2016. V. 670. P. 166 - 177.

Zamulaeva E. I., Levashov E. A., Kudryashov A. E. et al. Electrospark coatings deposited onto an Armco iron substrate with nano- and microstructured WC - Co electrodes: deposition process, structure, and properties // Surface & Coatings Technology. 2008. V. 202. P. 3715 - 3722.

Kuptsov K. A., Sheveyko A. N., Zamulaeva E. I. et al. Two-layer nanocomposite WC/a-C coatings produced by a combination of pulsed arc evaporation and electro-spark deposition in vacuum // Materials and Design. 2019. V. 167. No. 107645.

Talas S., Mertgenз E., Gokce B. ESD coating of copper with TiC and TiB2 based ceramic matrix composites // Materials Science and Engineering. 2016. V. 146. No. 012005.

Damma D. D., Contin A., Cardoso L. D. R. et al. A novel method to mitigate residual stress in CVD diamond film on steel substrates with a single intermediate layer // Surface & Coatings Technology. 2019. V. 357. P. 93 - 102.

Qiu L., Du Y., Wu L. et al. Microstructure, mechanical properties and cutting performances of TiSiCN super-hard nanocomposite coatings deposited using CVD method under the guidance of thermodynamic calculations // Surface and Coatings Technology. 2019. V. 378, No. 124956.

Guo C. T., Lee D., Chen P. C. Deposition of TiSiN coatings by arc ion plating process // Applied Surface Science. 2008. V. 254. P. 3130 - 3136.

Vega J., Scheerer H., Andersohn G., Oechsner M. Evaluation of the open porosity of PVD coatings through electrochemical iron detection // Surface & coatings technology. 2018. V. 350. P. 453 - 461.

Altun H., Sen S. The effect of PVD coatings on the corrosion behaviour of AZ91 magnesium alloy // Materials and Design. 2006. V. 27. P. 1174 - 1179.

Kayali Y. The corrosion and wear behavior of TiN and TiAlN coated AISI 316L stainless steel // Protection of Metals and Physical Chemistry of Surfaces. 2014. V. 50(3). P. 412 - 419.

Li S., Hu S., Hee A. C., Zhao Y. Surface modification of a Ti2AlC soft ceramic by plasma nitriding treatment // Surface & Coatings Technology. 2015. V. 281. P. 164 - 168.

Savonov G. S., Camarinha M. G. G., Rocha L. O. et al. Study of the influence of the RRA thermal treatment and plasma nitriding on corrosion behavior of 7075-T6 aluminum alloy // Surface & Coatings Technology. 2019. V. 374. P. 736 - 744.

Sizov I., Mishigdorzhiyn U., Leyens C. et al. Influence of thermocycle boroaluminising on strength of steel C30 // Surface Engineering. 2014. V. 30(2). P. 129 - 133.

Tьrkmen I., Yalamaзa E., Keddam M. Investigation of tribological behavior and diffusion model of Fe2B layer formed by pack-boriding on SAE 1020 steel // Surface & Coatings Technology. 2019. V. 377. № 124888.

Ballinger J., Catledge S. A. Metal-boride interlayers for chemical vapor deposited nanostructured NSD films on 316 and 440C stainless steel // Surface & Coatings Technology. 2015. V. 261. P. 244 - 252.

Kara R., Зolak F., Kayali Y. Investigation of wear and adhesion behaviors of borided steels // Transactions of the Indian Institute of Metals. 2016. V. 69. P. 1169 - 1177.

Ouladsaad S., Allaoui O., Daas A. Boro-aluminizing of XC38 steel // Indian Journal of Chemical Technology. 2019. V. 26. P. 239 - 243.

Ucar N., Turku N., Ozdemir A. F., Calik A. Boriding of binary Ni - Ti and ternary Ni - Ti - Cu shape memory alloys // Acta Physica Polonica A. 2016. V. 130. P. 492 - 495.

Khenifer M., Allaoui O., Taouti M. B. Effect of boriding on the oxidation resistance of 316L stainless steel // Acta Physica Polonica A. 2017. V. 132. P. 518 - 520.

Rayane K., Allaoui O., Allaoui A. Effect of diffusion annealing on borides layers produced on XC38 steel // Acta Physica Polonica A. 2017. V. 132. P. 521 - 523.

Carrera-Espinoza R., Figueroa-Lуpez U., Martнnez-Trinidad J. et al. Tribological behavior of borided AISI 1018 steel under linear reciprocating sliding conditions // Wear. 2016. V. 362 - 363. P. 1 - 7.

Cimenoglu H., Atar E., Motallebzadeh A. High temperature tribological behaviour of borided surfaces based on the phase structure of the boride layer // Wear. 2014. V. 309. P. 152 - 158.

Ozbek I., Bindal C. Mechanical properties of boronized AISI W4 steel // Surface and Coatings Technology. 2002. V. 154. P. 14 - 20.

Ozdemir O., Omar M. A., Usta M. et al. An investigation on boriding kinetics of AISI 316 stainless steel // Vacuum. 2009. V. 83. P. 175 - 179.

Zhan Z., He Y., Wang D., Gao W. Aluminide coatings formed on Fe - 13Cr steel at low temperature and its oxidation resistance // Oxidation of metals. 2007. V. 68. P. 243 - 251.

Sharafi S., Farhang M. R. Effect of aluminizing on surface microstructure of an HH309 stainless steel // Surface & Coatings Technology. 2006. V. 200. P. 5048 - 5051.

Vidakis N., Antoniadis A., Bilalis N. The VDI 3198 indentation test evaluation of a reliable qualitative control for layered compounds // Journal of Materials Processing Technology. 2003. V. 143 - 144. P. 481 - 485.

Heinke W., Leyland A., Matthews A. et al. Evaluation of PVD nitride coatings using impact, scratch and Rockwell-C adhesion tests // Thin Solid Films. 1995. V. 270. P. 431 - 438.

Uslu I., Comert H., Ipek M. et al. A comparison of borides formed on AISI 1040 and AISI P20 steels // Materials and Design. 2007. V. 28. P. 1819 - 1826.

Kartal G., Eryilmaz O. L., Krumdick G. et al. Kinetics of electrochemical boriding of low carbon steel // Applied Surface Science. 2011. V. 257. P. 6928 - 6934.

Kayali Y., Mertgenc E. Investigation of diffusion kinetic values of boronized AISI 303 steel by pack boronizing // Protection of Metals and Physical Chemistry of Surfaces. 2020. V. 56. P. 151 - 155.

Tsai W. T., Huang K. E. Microstructural aspect and oxidation resistance of an aluminide coating on 310 stainless steel // Thin Solid Films. 2000. V. 366. P. 164 - 168.

Chen F. S., Wang K. L. The kinetics and mechanism of multi-component diffusion on AISI 1045 steel // Surface and Coatings Technology. 1999. V. 115. P. 239 - 248.

Keddam M., Chentouf S. M. A diffusion model for describing the bilayer growth (FeB/Fe2B) during the iron powder-pack boriding // Applied Surface Science. 2005. V. 252. P. 393 - 399.

Jain V., Sundararajan G. Influence of the pack thickness of the boronizing mixture on the boriding of steel // Surface and Coatings Technology. 2002. V. 149. P. 21 - 26.

Kayali Y., Gokce B., Mertgenc E. et al. Analysis of wear behaviour of borided AISI 52100 steel with the taguchi method // Journal of the Balkan Tribological Association. 2013 (a). V. 19(3). P. 365 - 376.

Sina H., Corneliusson J., Turba K., Iyengar S. A study on the formation of iron aluminide (FeAl) from elemental powders // Journal of Alloys and Compounds. 2015. V. 636. P. 261 - 269.

Panda D., Kumar L., Alam S. N. Development of Al-Fe3Al nanocomposite by powder metallurgy route // Materials Today: Proceedings. 2015. V. 2. P. 3565 - 3574.

Stoloff N. S., Liu C. T., Deevi S. C. Emerging applications of intermetallics // Intermetallics. 2000. V. 8. P. 1313 - 1320.

Liu C. T., George E. P., Maziasz P. J., Schneibel J. H. Recent advances in B2 iron aluminide alloys: deformation, fracture and alloy design // Materials Science and Engineering A. 1998. V. 258. P. 84 - 98.

Badini C., Gianoglio C., Pradelli G. The effect of carbon, chromium and nickel on the hardness of boride layers // Surface and Coatings Technology. 1987. V. 30. P. 157 - 170.

Li C., Shen B., Li G., Yang C. Effect of boronizing temperature and time on microstructure and abrasion wear resistance of Cr12Mn2V2 high chromium cast iron // Surface and Coatings Technology. 2008. V. 202 (24). P. 5882 - 5886.

Kayali Y., Yalзin Y. Investigation of diffusion kinetics of boronized AISI 316L stainless steel // Journal of Materials and Mechatronics: A. 2020. V. 1(1). P. 12 - 21.

Ozdemir O., Usta M., Bindal C., Ucisik A. H. Hard iron boride (Fe2B) on 99.97 wt% pure iron // Vacuum. 2006. V. 80. P. 1391 - 1395.

Yazdani A. R., Rafiei M. Characterization and wear properties of Fe3Al and (Fe, Ti)3Al intermetallic claddings produced by GTAW process // Protection of Metals and Physical Chemistry of Surfaces. 2019. V. 55(6). P. 1142 - 1147.

Kayali Y., Bьyьksagis A., Yalcin Y. Corrosion and wear behaviors of boronized AISI 316L stainless steel // Metals and Materials International. 2013(b). V. 19. P. 1053 - 1061.

Ghosh G., Sidpara A., Bandyopadhyay P. P. Understanding the role of surface roughness on the tribological performance and corrosion resistance of WC - Co coating // Surface and Coatings Technology. 2019. V. 378. № 125080.




DOI: https://doi.org/10.30906/mitom.2021.7.46-53

© Издательский дом «Фолиум», 1998–2025